One Shot

One Shot can be applied from 1/16″ to 1/2″ to renew balconies, industrial floors, loading docks, and ramps.

Where to use:

Resurface balconies, parking decks, industrial floors, loading docks, and ramps.

How to apply:

Trowel or spray. Additional Information

Performance Characteristics

  • Low shrinkage Maintains integrity of repair, resists cracking.
  • Thermal compatibility Prevents delamination due to temperature change.
  • Durable Resistant to weathering action, excellent freeze/thaw stability and abrasion resistance.
  • Very low permeability Resistant to deicing salts, carbonation, chloride, and chemical attack.
  • Dimensionally stable Ideal for large areas.
  • Abrasion resistant Hard, durable surface for long term wear.
  • High early strength Open to foot traffic in 24 hours, pneumatic tire in 72 hours.

Surface Preparation

  • Remove loose and deteriorated material, laitance, dirt, dust, oil and any surface contaminants that will inhibit proper bond.
  • Saw cut edges with a diamond blade at a 90° angle to eliminate feather edging. Avoid polishing the edges as this will inhibit bond.
  • Remove a minimum 1/16 inch of surface (CSP 5) by abrasive blasting, steel shotblasting, scarifying, needle-scaling or high pressure water.
  • Avoid bruising or micro cracking during surface preparation. Refer to ICRI Surface Preparation Guide 03732.
  • Repair zone must be a minimum of 1/8 inch deep, of simple geometry, with no complex edge conditions.
  • Avoid long narrow repairs; these have a tendency to crack.
  • Apply Conpro Start where consolidant is of benefit.
  • Saturate substrate with clean water, (saturated surface dry/SSD), with no standing water during Priming or Application.
  • Remove concrete from corroded steel and several inches beyond to expose non-corroded steel.
  • Provide a 3/4 inch clearance between the concrete and steel.
  • Damaged reinforcing steel should be inspected by a qualified engineer and appropriate action taken.

Priming

  • Concrete Use Conpro Primer, as a bonding primer. Refer to the individual product technical data bulletin for information. Alternatively, prime the prepared substrate including all edges with a slurry coat of the repair mortar. Work the slurry into the substrate to ensure intimate contact and establish bond. The repair material must be applied while slurry is wet. If the slurry dries, remove and recoat.
  • Reinforcing Steel Remove all scaling rust from reinforcing steel. Apply ECB anti-corrosion coating.

Mixing

  • Mechanically mix using a low speed drill (400-600 rpm) and mixing paddle or mortar mixer.
  • Pour 3 quarts of potable water into a clean mixing vessel and slowly add all of the powder.
  • Mix continuously for 3 minutes to a uniform, lump-free consistency.
  • Add up to 1 pint of additional water, if needed.
  • Allow to “breathe” for 1 minute and remix for 1 minute. This will improve workability and open time.
  • Do not overmix, as this will entrain excess air.

Application

  • At the time of application, surfaces should be saturated surface dry (SSD) but hold no standing water.
  • Follow instructions for Priming.
  • Trowel in key coat.
  • Double back applying material necessary to complete application.
  • Apply with a motion similar to placing concrete.
  • Form applications must be consolidated with vibrator.
  • Finish with a magnesium float or trowel.
  • Do not overwork the finish.
  • For applications over 1/2 inch, add up to 30 lbs. of 3/8 inch aggregate. Aggregate must be non-reactive, low absorption, graded and high density.

Curing

  • Dampen the repair with a fine mist of water for 24 hours or moist cure with wet burlap and polyethylene. Alternatively, apply ProMasonry Cure & Seal.
  • Protect repair from direct sunlight, wind, rain and frost during curing period.

Clean Up

  • Clean tools and equipment with water immediately after use.
  • Cured material must be removed mechanically.

Coverage/Yield

  • 0.42 ft³/50 lbs.
  • 0.65 ft³ when extended with 30 lbs. of 3/8 inch aggregate.

Product Handling

  • Packaging 50 lbs. paper bags.
  • Shelf Life 12 months when properly stored.
  • Storage Transport and store in cool, clean, dry conditions in unopened containers. High temperature or high humidity will reduce shelf life.

Limitations

  • Do not apply unless substrate and ambient temperature can be maintained at a minimum of 40°F for 24 hours. Refer to ACI Cold Weather Application Guidelines.
  • Cold mixing water and low temperature will retard set. Hot water and high temperature will accelerate set.
  • Protect application from precipitation and high wind for at least 8 hours.
  • Do not mix more material than can be placed in 30 minutes.
  • Do not re-tember, this will damage the cross-linking of the polymer and cause cracking and loss of bond.
  • Do not add more water than specified – this will lower strength and cause shrinkage cracking.
  • Avoid overworking material during placement and finishing – this will produce surface (map) cracking.

Health and Safety

  • Product is alkaline.
  • Do not ingest.
  • Avoid breathing dust.
  • Avoid contact with skin and eyes.
  • Refer to Safety Data Sheet (SDS) for additional information.

First Aid

  • In case of skin contact, wash thoroughly with soap and water.
  • In case of eye contact, flush with a high volume of water for at least 15 minutes and contact a medical professional.
  • For respiratory problems, remove person to fresh air.

Disposal

  • Dispose of material in accordance with local, state and federal regulations.
  • Technical Data
  • Data Bulletin
  • CSI Spec
  • Competition
  • Curing
  • Pump & Spray
  • FAQs
  • Safety Data Sheet

Physical state and appearance

 

Fine, gray powder

Base

 

Portland cement

pH

Wet mix

>12

Aggregate type

 

Sharp quartz silica

Water/cement ratio

 

0.48*

Density

Wet mix

110 lbs./ft.³

Setting time by vicat needle

ASTM C191

Initial 200 minutes – Final 245 minutes

Percent air by volumetric

ASTM C173

6%

Resistance to deicing chemicals under freeze/thaw

ASTM C672

50 cycles – 0 rating – no effect

Length change

ASTM C157

< 1000 μstrains @ 28 days – air cure

< 500 μstrains @ 28 days – wet cure

Slant shear bond strength - epoxy

ASTM C882

1500 psi – without slurry coat

2000 psi – with slurry coat

  

1 Day

7 Days

14 Days

28 Days

Compressive strength – psi

ASTM C109

1740

4500

 

5000

Flexural strength – 3 point loading - psi

ASTM C78

   

1010

Tensile strength – psi

ASTM C307

 

600

640

740

*Test run using 3 quarts water per 50 lbs. bag of Conpro One Shot.

FOR PROFESSIONAL USE ONLY

Conproco warrants this product for one year from the date of manufacture to be free from manufacturing defects and to meet the technical properties on the current technical data sheet if used as directed within shelf life. User determines suitability of product for use and assumes all risks. Buyer's sole remedy shall be limited to the purchase price or replacement of product, exclusive of labor or cost of labor. January 8, 2016.

NO OTHER WARRANTIES EXPRESSED OR IMPLIED SHALL APPLY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. CONPROCO CORP SHALL NOT BE LIABLE UPON ANY LEGAL THEORY FOR SPECIAL OR CONSEQUENTIAL DAMAGES.

Conproco
BASF
Euclid / Tamms
Mapei
Sika
USCP
MasterEmaco N400 RS; MasterEmaco N400; MasterEmaco N350 CI; MasterEmaco N423 RS; MasterEmaco N425; MasterEmaco N426
Euco Repair V100; Verticoat; Verticoat Supreme; Speed Crete PM
Planitop X; Planitop XS
SikaTop 123; SikaRepair SAJ; SikaRepair HSB; Monotop 615
Thin Patch V/O
MasterEmaco N424; MasterEmaco N205; MasterEmaco N220
EucoPatch; Speed Crete Red Line
Planitop X; Planitop XS
Sika Repair 223; SikaQuick VOH; SikaRepair SHA; SikaRepair SHB
HP Multi-Purpose Repair Mortar
MasterEmaco S488 CI; MasterEmaco S487 SP
Tamms Structural Mortar
Planitop 12
SikaRepair 224; SikaRepair SHB; SikaCem Monotop 615
None
MasterEmaco S440; MasterEmaco S440 CI; MasterEmaco S447 MC; MasterEmaco S466 CI; MasterEmaco S47 7CI
EucoCrete; Tamms Form & Pour; EucoRepair SCC
Planitop 15; Planitop FD; Planitop 11 SCC;
SikaCrete 211; SikaCrete 211 SC Plus; MonoTop 611; SikaTop 111 Plus
Deckmix AE
MasterEmaco T310 CI
Concrete-Top Supreme; Thin Top Supreme; Euco Re-Cover
Mapecem 102
SikaRepair 222 w/LatexR
None
MasterEmaco N424; MasterEmaco N205; MasterEmaco N220
EucoPatch; Speed Crete Red Line
Planitop X; Planitop XS
SikaRepair 223; SikaQuick VOH; SikaRepair SHA; SikaRepair SHB
None
MasterEmaco T310 CI; MasterEmaco S446 CI; MasterEmaco S487 SP; MasterEmaco S488 CI
Concrete-Top Supreme; Thin Top Supreme; Euco Re-Cover; EucoRepair SCC; Tamms Structural Mortar
Mapecem 102; Planitop 11 SCC; Planitop 12
SikaRepair 222 w/LatexR; SikaCrete 211; SikaCrete 211 SC Plus; SikaRepair 224; SikaRepair SHB; SikaCem Monotop 615
Deckmix AE
None
None
None
None
None

Cementitous Products

Product
Minimum Temperature
Minimum to 55° F
55°F – 70° F
70° F and above
Minimum Time to Coat
ISR CM
40°
12 Hours
4 Hours
2 Hours
3 to 5 days depending on temperature
ISR VO
40°
12 Hours
4 Hours
2 Hours
3 to 5 days depending on temperature
ISR AG
40°
12 Hours
4 Hours
2 Hours
3 to 5 days depending on temperature
Conpro Set
40°
12 Hours
4 Hours
2 Hours
3 to 5 days depending on temperature
Quick Shot
40°
8 Hours
2 Hours
1 Hour
3 to 5 days depending on temperature
Forment (remove forms)
40°
72 Hours
48 Hours
24 Hours
3 to 5 days depending on temperature
Gun Shot LPS
40°
12 Hours
4 Hours
2 Hours
3 to 5 days depending on temperature
Injection Grout (remove clay)
40°
24 Hours
24 Hours
24 Hours
3 to 5 days depending on temperature
One Shot
40°
24 Hours
12 Hours
6 Hours
3 to 5 days depending on temperature
Matrix
40°
12 Hours
4 Hours
2 Hours
3 to 5 days depending on temperature
Matrix TR
40°
12 Hours
4 Hours
2 Hours
3 to 5 days depending on temperature
Repoint
40°
12 Hours
4 Hours
2 Hours
3 to 5 days depending on temperature
Plastermix
40°
12 Hours
4 Hours
2 Hours
3 to 5 days depending on temperature
Structural Skin
40°
12 Hours
4 Hours
2 Hours
3 to 5 days depending on temperature
Conpro One Coat
40°
12 Hours
4 Hours
2 Hours
3 to 5 days depending on temperature
Conpro Stucco
40°
12 Hours
4 Hours
2 Hours
3 to 5 days depending on temperature
Foundation Coat
40°
12 Hours
4 Hours
2 Hours
3 to 5 days depending on temperature
Super Seal
40°
12 Hours
4 Hours
2 Hours
3 to 5 days depending on temperature

Liquid Products

Product
Minimum Temperature
Minimum to 55° F
55°F – 70° F
70° F and above
Minimum Time to Coat
Conpro Start
40°
18 Hours
12 Hours
6 Hours
Refer to temperature
ECB
40°
8 Hours
1 Hour
30 Minutes
Dry to touch
Primer
40°
8 Hours
1 Hour
30 Minutes
Color change to orange
Shield MX
40°
24 Hours
18 Hours
12 Hours
Dry to touch
M3P & M3P-X
45°
24 Hours
18 Hours
12 Hours
Dry to touch
M3P Overcoat
45°
24 Hours
18 Hours
12 Hours
Dry to touch
Conpro Lastic
45°
24 Hours
18 Hours
12 Hours
Dry to touch
Color Coat
45°
24 Hours
18 Hours
12 Hours
Dry to touch
Super Color Stain
45°
24 Hours
18 Hours
12 Hours
Dry to touch
Elastideck
45°
24 Hours
18 Hours
12 Hours
Dry to touch
Terra Color
45°
24 Hours
18 Hours
12 Hours
Dry to touch
Terracotta Finish
45°
24 Hours
18 Hours
12 Hours
Dry to touch

SPRAY AND PUMPING EQUIPMENT

CEMENT BASED MATERIALS

The gallons per minute volume of a rotor/stator pump is determined by the pump size. The pressure capacity of a pump is determined by the number of stages. Thicker materials and longer distances require higher pressure.

Manufacturer Web Addresses

LIQUIDS AND COATINGS

The capacity of airless spray equipment is determined by the tip size. Given the proper tip size, the manufacturer of the equipment will be able to recommend specific equipment.

Manufacturer Web Addresses

Surface must be clean of loose material, dust, and contaminants that inhibit bond. Mechanically remove a minimum of 1/16" of surface.

Conpro Primer is recommended.  In large open areas keeping the surface damp can be problematic. The alternative is to saturate substrate with clean water (SSD) with no standing water.

Apply with a motion similar to placing concrete. Finish with a magnesium float or trowel.  Do not over work the finish as this can induce surface cracking. 

Up to 30 lbs of 3/8" aggregate can be added to a 50 lb. bag of One Shot

Projects Showcase

Sutton Place

Project History

The deterioration of the balconies was significant enough to warrant complete replacement of the concrete. Once the demolition was complete the steel reinforcing was coated with ECB. One Shot Ag was mixed and placed into forms. Once cured, Conpro Shield M was applied for long lasting protection.

Contractor
Astro Waterproofing,
New York, NY

Bryant University

Project History

Bryant University, founded in 1863, is one of the top business schools in the United States. Visitors are likely to be foreign dignitaries presenting lectures, busy executives taking advantage of Bryant’s development programs or recruiters from some of the nation’s top firms. The outdoor staircase leading into the Student Center exhibited signs of deterioration and was showing some exposed rebar and failing concrete, which needed to be repaired. The university had to work quickly to restore the campus’ professional appearance. The Waterproofing Company started by using bushhammers to get down to clean, sound concrete. Conpro Primer was used to provide a Velcro-like connection between the substrate and repair materials. Conpro Set was used to repair the vertical surfaces, while One Shot Ag was used to repair horizontal surfaces. Top Coat specially suited for areas facing pedestrian traffic provided a clean and skid-resistant finish, as well as added waterproofing protection.

Products
Conpro Primer
Conpro Set
One Shot Ag

Contractor
The Waterproofing Co.,
Boston, MA

Associated Products